| Peer-Reviewed

Analytical Behaviour of BPS150-36 Polycrystalline Modules Electrical Parameters with Ambient Temperature Under Standard Conditions Using Servant Model

Received: 20 June 2019     Accepted: 23 July 2019     Published: 21 October 2021
Views:       Downloads:
Abstract

(PV)-cells/modules demonstrated low performance in hot-humid climates because elevated ambient temperature conditions significantly influence their performance. We investigated analytically the behaviour of BPS150-36 polycrystalline silicon (PV)-modules electrical parameters with ambient temperature under standard irradiation conditions (STC), using Servant model. Matlab and r.getdata have been used for the numerical simulations. Results obtained show that (JPh) increases exponentially from 7.67% to 65.87% with temperature. (RS) increases linearly by 7.6% and 9.18% while (VOC) decreases from 19.4 % to 17.6% and (RSh) decreases approximately by 12.6% and 4.8%. The obtained power output (P) losses had been 82.31 % and 31.56%, and the overall linear losses in efficiency (η) had been approximately 27.84% and 5.02 %, while (JS) increases exponentially from 3.87% to 15.75%. The increase in (JPh) with temperature can be attributed to the increased in light absorption owing to a decrease in the bandgap of silicon. The decrease in (η) with temperature is mainly controlled by the decrease in (VOC) and fill factor (FF) with T. Power output loss is strongly attributed to the decrease of the fill factor (FF) due to an increase in series resistance (RS) and therefore caused by the (JSC) degradation.

Published in International Journal of Sustainable and Green Energy (Volume 10, Issue 4)
DOI 10.11648/j.ijrse.20211004.11
Page(s) 108-120
Creative Commons

This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited.

Copyright

Copyright © The Author(s), 2021. Published by Science Publishing Group

Keywords

Low Performance, Behaviour, Standard Irradiation Condition, Servant Model, Increase, Decrease, Degradation

References
[1] Schneller E J., Brooker R P., Shiradkar N S., Dhere N G., Davis K O., Seigneur H P., Mohajeri N., Wohlgemuth J., Scardera G., Rudack A C., Schoenfeld W V. (2016): Manufacturing metrology for c-Si module reliability and durability Part III: Module manufacturing. Renewable and Sustainable Energy Reviews, 59: 992-1016.
[2] Parretta A., Bombace M., Graditi G., Schioppo R. (2005): Optical degradation of long-term, field-aged c-Si photovoltaic modules. Solar Energy Materials and Solar Cells, 86: 349-364.
[3] Kahoul N., Houabes M., Sadok M. (2014): Assessing the early degradation of photovoltaic modules performance in the Saharan region. Energy Conversion and Management, 82: 320-326.
[4] Munoz M A., Alonso-Garcı M C., Vela N., Chenlo F. (2011): Early degradation of silicon PV modules and guaranty conditions. Solar Energy, 85: 2264-2274.
[5] Ketola B., Shirk C., Griffith P. (2011): Encapsulation performance comparison of PV modules in outdoor arrays. In Proceedings of the 26th European Photovoltaic Solar Energy Conference and Exhibition, 3144-3151.
[6] Sharma V., Chandel S S. (2013): Performance and degradation analysis for long term reliability of solar photovoltaic systems: A review. Renewable Sustainable Energy Reviews, 27: 753-767.
[7] Dubey R., Chattopadhyayl S., Kuthanazhil V., Johnl J J., Vasil J., Kottantharayill A., Arora B M., Narsimhanl K L., Kuber V., Solanki C S., Kumar A., Sastry O S. (2014): Performance degradation in field-aged crystalline silicon PV modules in different Indian climatic conditions. In Proceedings of the IEEE 40th Photovoltaic Specialists Conference, 3182-3187.
[8] Kichou S., Santiago S., Gustavo N., Torres R M., Chouder A., Guasch D. (2016): Characterization of degradation and evaluation of model parameters of amorphous silicon photovoltaic modules under outdoor long-term exposure. Energy, 96: 231-241.
[9] Park N C., Jeong J S., Kang B J., Kim D H. (2013): The effect of encapsulant discoloration and delamination on the electrical characteristics of photovoltaic module. Microelectronics Reliability, 53: 1818-1822.
[10] Tossa A K., Soro Y M., Thiaw L., Azoumah Y., Sicot L., Yamegueu D., Lishou C., Coulibaly Y., Razongles G. (2016): Energy performance of different silicon photovoltaic technologies under hot and harsh climate. Energy, 103: 261-270.
[11] Canete C., Carretero J., Cardona S M. (2014): Energy performance of different photovoltaic module technologies under outdoor conditions. Energy, 65: 295-302.
[12] Makrides G., Zinsser B., Georghiou G E., Schubert M., Werner J H. (2009): Temperature behaviour of different photovoltaic systems installed in Cyprus and Germany. Solar Energy Materials and Solar Cells, 93: 1095-9.
[13] Amrouche B., Sicot L., Guessoum A., Belhamel M. (2013): Experimental analysis of the maximum power point's properties for four photovoltaic modules from different technologies: monocrystalline and polycrystalline silicon, CIS and CdTe. Solar Energy Materials and Solar Cells, 118: 124-34.
[14] Khan F., Singh S N., Husain M. (2010): Effect of illumination intensity on cell parameters of a silicon solar cell. Solar Energy Materials and Solar Cells, 94: 1473-6.
[15] Singh P., Ravindra N M. (2012): Temperature dependence of solar cell performance-ananalysis. Solar Energy Mater Sol Cells, 101: 36-45.
[16] Meral M E., Dincer F. (2011): A review of the factors affecting operation and efficiency of photovoltaic based electricity generation systems. Renewable and Sustainable Energy Reviews, 15: 2176-84.
[17] Sanchez Reinoso C R., Milone D H., Buitrago R H. (2010): Efficiency study of different photovoltaic plant connection schemes under dynamic shading. International Journal of Hydrogen Energy, 35: 5838-43.
[18] Nagae S, Toda M, Minemoto T, Takakura H, Hamakawa Y. (2006): Evaluation of the impact of solar spectrum and temperature variations on output power of silicon-based photovoltaic modules. Solar Energy Materials and Solar Cells, 90: 3568-75.
[19] Park K., Kang G., Kim H., Yu G., Kim J. (2010): Analysis of thermal and electrical performance of semi-transparent photovoltaic (PV) module. Energy, 35: 2681-7.
[20] Géraud F H., Basile B K., Macaire A., Irénée V M. (2018): Degradation of Crystalline Silicon Photovoltaic Cells/Modules under Heat and Temperature Effect. Physical Science International Journal, 19: 1-12.
[21] Sanchez-Friera P., Piliougine M., Peläez J., Carretero J., Cardona M S. (2011): Analysis of degradation mechanisms of crystalline silicon PV modules after 12 years of operation in Southern Europe. Progress in Photovoltaics Research and Application, 19: 658-666.
[22] Joseph M K., Rong P., Tamizhmani G S. (2014): Investigation of dominant failure mode (s) for field-aged crystalline silicon PV modules under desert climatic conditions. IEEE Journal of Photovoltaics, 4: 814-826.
[23] Sharma V., Kumar A., Sastry O S., Chandel S S. (2011): Performance assessment of different solar photovoltaic technologies under similar outdoor conditions. Energy, 58: 511-551.
[24] Alshushan M A., Saleh I M. (2013): Power degradation and performance evaluation of PV modules after 31 years of work. IEEE 39th Photovoltaic Specialists Conference, 2977-2982.
[25] Pramod R., Tiwari G N., Sastry O S., Birinchi B., Vikrant S. (2016): Degradation of monocrystalline photovoltaic modules after 22 years of outdoor exposure in the composite climate of India. Solar Energy, 135: 786-795.
[26] Huili H., Xian D., Haiwen L., Huan Y., Kai Z., Jiangfeng L., Verlinden P J., Zongcun L., Hui S. (2018): Analysis of the Degradation of Monocrystalline Silicon Photovoltaic Modules After Long-Term Exposure for 18 Years in a Hot-Humid Climate in China. IEEE Journal of Photovoltaics, 8: 806-812.
[27] Dunlop E D., Halton D. (2006): The performance of crystalline silicon photovoltaic solar modules after 22 years of continuous outdoor exposure. Progress in Photovoltaics Reseach and Applications, 14: 53-64.
[28] Sakamoto S., Oshiro T. (2003): Field test results on the stability of crystalline silicon photovoltaic modules manufactured in the 1990’s. In 3rd World Conference on Photovoltaic Energy Conversion, Osaka, Japan, 1888-1891.
[29] Sastry O S., Saurabh S., Shil S K., Pant P C., Kumar R., Bandyopadhyay B. (2010): Performance analysis of field exposed single crystalline silicon modules. Solar Energy Materials and Solar Cells, 94: 1463-1468.
[30] Jordan D C., Kurtz S R. (2013): Photovoltaic degradation rates-an analytical review. Progress in Photovoltaics Research and Application, 21: 12-29.
[31] Chandel S S., Naik M N., Sharma V., Chandel R. (2015): Degradation analysis of 28-year field exposed mono-c-Si photovoltaic modules of a direct coupled solar water pumping system in western Himalayan region of India. Renewable Energy, 78: 193-202.
[32] Ndiaye A., Kebe C M F., Charki A., Ndiaye P A., Sambou V., Kobi A. (2014): Degradation evaluation of crystalline-silicon photovoltaic modules after a few operation years in a tropical environment. Solar Energy, 103: 70-77.
[33] Bouraiou A., Hamouda M., Chaker A., Mostefaoui M., Lachtar S., Sadok M., Boutasseta N., Othmani M., Issam A. (2015): Analysis and evaluation of the impact of climatic conditions on the photovoltaic modules performance in the desert environment. Energy Conversion and Management, 106: 1345-1355.
[34] Ndiaye A., Kobi A., Charki A., Sambou V. (2013): Degradations of silicon photovoltaic modules: A literature review. Solar Energy, 96: 140-151.
[35] Servant J. (1976): Calculation of cell temperature for photovoltaic modules from climatic data, Proceedings of the 9th Biennial Congress of the International Solar Energy Society- Intersol, Montreal, Canada, 3: 1640-1643.
[36] Rouholamini A., Pourgharibshahi H., Fadaeinedjad R., Abdolzadeh M. (2014): Temperature of a photovoltaic module under the influence of different environmental conditions-experimental investigation. International Journal of Ambient Energy, 37: 266-272.
[37] Radziemska E. (2003): The effect of temperature on the power drop in crystalline silicon solar cells. Renewable Energy, 28: 1-12.
[38] Siddiqui M U., Abido M. (2013): Parameter estimation for five and seven-parameter photovoltaic electrical models using evolutionary algorithms. Applied Softward Computing, 13: 4608-4621.
[39] Ma T., Yang H., Lu L. (2014): Development of a model to simulate the performance characteristics of crystalline silicon photovoltaic modules/strings/arrays. Solar Energy, 100: 31-41.
[40] Bai J., Liu S., Hao Y., Zhang Z., Jiang M., Zhang Y. (2014): Development of a new compound method to extract the five parameters of PV modules. Energy Conversion and Management, 79: 294-303.
[41] Attivissimo F., Adamo F., Carullo A., Lanzolla A M L., Spertino F., Vallan A. (2013): On the performance of the double-diode model in estimating the maximum power point for different photovoltaic technologies. Measurement, 46: 3549-3559.
[42] Ishaque K., Salam Z., Syafaruddin A. (2011): Comprehensive MATLAB Simulink PV system simulator with partial shading capability based on two-diode model. Solar Energy, 85: 2217-2227.
[43] Ishaque K., Salam Z., Taheri H. (2011): Simple, fast and accurate two-diode model for photovoltaic modules. Solar Energy Materials and Solar Cells, 95: 586-594.
[44] Tossa A K., Soro Y M., Azoumah Y., Yamegueu D. (2014): A new approach to estimate the performance and energy productivity of photovoltaic modules in real operating conditions. Solar Energy, 110: 543-560.
[45] Ghani F., Duke M., Carson J. (2013): Numerical calculation of series and shunt resistance of a photovoltaic cell using the Lambert W-function: experimental evaluation. Solar Energy, 87: 246-253.
[46] Ghani F., Duke M. (2011): Numerical determination of parasitic resistances of a solar cell using the Lambert W-function. Solar Energy, 85: 2386-2394.
[47] Alami A H. (2014): Effects of evaporative cooling on efficiency of photovoltaic modules. Energy Conversion Management, 77: 668-79.
[48] Meyer E L., van Dyk E E. (2004): Assessing the reliability and degradation of photovoltaic module performance parameters. IEEE Transactions on Reliability, 53: 83-92.
[49] Daliento S., Lancellotti L. (2010): 3D analysis of the performances degradation caused by series resistance in concentrator solar cells. Solar Energy, 84: 44-50.
[50] Alonso G M C., Balenzategui J L. (2004): Estimation of photovoltaic module yearly temperature and performance based on Nominal Operation Cell Temperature calculations. Renewable Energy, 29: 1997-2010.
[51] Skoplaki E., Palyvos, J A. (2009): On the temperature dependence of photovoltaic module electrical performance: A review of efficiency/power correlations. Solar Energy, 83: 614-624.
[52] Zondag H A. (2008): Flat-plate PV-thermal collectors and systems - a review. Renewable and Sustainable Energy Reviews, 12: 891-959.
[53] Garg H P., Agarwal R K. (1995): Some aspects of a PV/T collector/forced circulation flat plate solar water heater with solar cells. Energy Conversion and Management, 36: 87-99.
[54] Evans D L., Florschuetz L W. (1978): Terrestrial concentrating photovoltaic power system studies. Solar Energy, 20: 37-43.
[55] Evans D L. (1981): Simplified method for predicting photovoltaic array output. Solar Energy, 27: 555-560.
[56] Kou Q., Klein S A., Beckman W A. (1998): A method for estimating the long-term performance of direct-coupled PV pumping systems. Solar Energy, 64: 33-40.
[57] Siegel M D., Klein S A., Beckman W A. (1981): A simplified method for estimating the monthly-average performance of photovoltaic systems. Solar Energy, 26: 413-418.
[58] Jie J., Hua Y., Gang P., Bin J., Wei H. (2007): Study of PV-Trombe wall assisted with DC fan. Building and Environment, 42: 3529-3539.
[59] Evdokimov V M., Maiorov V A. (2017): A Study of Limiting Energy and Temperature Characteristics of Photovoltaic Solar Radiation Converters. Applied Solar Energy, 53: 1-9.
[60] Chengquan X., Xuegong Y., Deren Y., Duanlin Q. (2014): Impact of solar irradiance intensity and temperature on the performance of compensated crystalline silicon solar cells. Solar Energy Materials and Solar Cells, 128: 427-434.
[61] Kahoul N., Chenni R., Cheghib H., Mekhilef S. (2017): Evaluating the reliability of crystalline silicon photovoltaic modules in harsh environment. Renewable Energy, 109: 66-72.
Cite This Article
  • APA Style

    Hounkpatin Florentin Géraud, Madogni Vianou Irénée, Agbomahéna Bienvenu Macaire, Kounouhéwa Bruno Basile. (2021). Analytical Behaviour of BPS150-36 Polycrystalline Modules Electrical Parameters with Ambient Temperature Under Standard Conditions Using Servant Model. International Journal of Sustainable and Green Energy, 10(4), 108-120. https://doi.org/10.11648/j.ijrse.20211004.11

    Copy | Download

    ACS Style

    Hounkpatin Florentin Géraud; Madogni Vianou Irénée; Agbomahéna Bienvenu Macaire; Kounouhéwa Bruno Basile. Analytical Behaviour of BPS150-36 Polycrystalline Modules Electrical Parameters with Ambient Temperature Under Standard Conditions Using Servant Model. Int. J. Sustain. Green Energy 2021, 10(4), 108-120. doi: 10.11648/j.ijrse.20211004.11

    Copy | Download

    AMA Style

    Hounkpatin Florentin Géraud, Madogni Vianou Irénée, Agbomahéna Bienvenu Macaire, Kounouhéwa Bruno Basile. Analytical Behaviour of BPS150-36 Polycrystalline Modules Electrical Parameters with Ambient Temperature Under Standard Conditions Using Servant Model. Int J Sustain Green Energy. 2021;10(4):108-120. doi: 10.11648/j.ijrse.20211004.11

    Copy | Download

  • @article{10.11648/j.ijrse.20211004.11,
      author = {Hounkpatin Florentin Géraud and Madogni Vianou Irénée and Agbomahéna Bienvenu Macaire and Kounouhéwa Bruno Basile},
      title = {Analytical Behaviour of BPS150-36 Polycrystalline Modules Electrical Parameters with Ambient Temperature Under Standard Conditions Using Servant Model},
      journal = {International Journal of Sustainable and Green Energy},
      volume = {10},
      number = {4},
      pages = {108-120},
      doi = {10.11648/j.ijrse.20211004.11},
      url = {https://doi.org/10.11648/j.ijrse.20211004.11},
      eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.ijrse.20211004.11},
      abstract = {(PV)-cells/modules demonstrated low performance in hot-humid climates because elevated ambient temperature conditions significantly influence their performance. We investigated analytically the behaviour of BPS150-36 polycrystalline silicon (PV)-modules electrical parameters with ambient temperature under standard irradiation conditions (STC), using Servant model. Matlab and r.getdata have been used for the numerical simulations. Results obtained show that (JPh) increases exponentially from 7.67% to 65.87% with temperature. (RS) increases linearly by 7.6% and 9.18% while (VOC) decreases from 19.4 % to 17.6% and (RSh) decreases approximately by 12.6% and 4.8%. The obtained power output (P) losses had been 82.31 % and 31.56%, and the overall linear losses in efficiency (η) had been approximately 27.84% and 5.02 %, while (JS) increases exponentially from 3.87% to 15.75%. The increase in (JPh) with temperature can be attributed to the increased in light absorption owing to a decrease in the bandgap of silicon. The decrease in (η) with temperature is mainly controlled by the decrease in (VOC) and fill factor (FF) with T. Power output loss is strongly attributed to the decrease of the fill factor (FF) due to an increase in series resistance (RS) and therefore caused by the (JSC) degradation.},
     year = {2021}
    }
    

    Copy | Download

  • TY  - JOUR
    T1  - Analytical Behaviour of BPS150-36 Polycrystalline Modules Electrical Parameters with Ambient Temperature Under Standard Conditions Using Servant Model
    AU  - Hounkpatin Florentin Géraud
    AU  - Madogni Vianou Irénée
    AU  - Agbomahéna Bienvenu Macaire
    AU  - Kounouhéwa Bruno Basile
    Y1  - 2021/10/21
    PY  - 2021
    N1  - https://doi.org/10.11648/j.ijrse.20211004.11
    DO  - 10.11648/j.ijrse.20211004.11
    T2  - International Journal of Sustainable and Green Energy
    JF  - International Journal of Sustainable and Green Energy
    JO  - International Journal of Sustainable and Green Energy
    SP  - 108
    EP  - 120
    PB  - Science Publishing Group
    SN  - 2575-1549
    UR  - https://doi.org/10.11648/j.ijrse.20211004.11
    AB  - (PV)-cells/modules demonstrated low performance in hot-humid climates because elevated ambient temperature conditions significantly influence their performance. We investigated analytically the behaviour of BPS150-36 polycrystalline silicon (PV)-modules electrical parameters with ambient temperature under standard irradiation conditions (STC), using Servant model. Matlab and r.getdata have been used for the numerical simulations. Results obtained show that (JPh) increases exponentially from 7.67% to 65.87% with temperature. (RS) increases linearly by 7.6% and 9.18% while (VOC) decreases from 19.4 % to 17.6% and (RSh) decreases approximately by 12.6% and 4.8%. The obtained power output (P) losses had been 82.31 % and 31.56%, and the overall linear losses in efficiency (η) had been approximately 27.84% and 5.02 %, while (JS) increases exponentially from 3.87% to 15.75%. The increase in (JPh) with temperature can be attributed to the increased in light absorption owing to a decrease in the bandgap of silicon. The decrease in (η) with temperature is mainly controlled by the decrease in (VOC) and fill factor (FF) with T. Power output loss is strongly attributed to the decrease of the fill factor (FF) due to an increase in series resistance (RS) and therefore caused by the (JSC) degradation.
    VL  - 10
    IS  - 4
    ER  - 

    Copy | Download

Author Information
  • Département de Physique (FAST/LPR), Université d’Abomey-Calavi (UAC), Abomey-Calavi, Bénin

  • Département de Physique (FAST/LPR), Université d’Abomey-Calavi (UAC), Abomey-Calavi, Bénin

  • Département de Physique (FAST/LPR), Université d’Abomey-Calavi (UAC), Abomey-Calavi, Bénin

  • Département de Physique (FAST/LPR), Université d’Abomey-Calavi (UAC), Abomey-Calavi, Bénin

  • Sections